Motorola PMDN4060 BPR40, BPR20 Cloning Cable

Part Number: PMDN4060

    This combination does not exist.

    17.95 17.95 17.95 USD Motorola Mag One PMDN4060AR Cable & Instructions How to Clone BPR40 or BPR20 2-Way Radios

    17.95

    Option not available

    Add to Cart

    Free Shipping in U.S. on orders over $299

    Share:

    Motorola Mag One PMDN4060AR Cloning Cable for BPR40, BPR20 2-Way Radios


    Clone additional Mag One BPR radios using your radio and cloning cable. No software or computer is needed. All settings are transferred to the new BPR radios including frequencies, power settings, and button assignments.

    This accessory makes it easy to buy additional radios and not have to worry about programming information. Models must be identical. Remove the batteries from both radios and make sure the model numbers (starts with AAH84) are an exact match. If not, you cannot use this cable.

    How To Clone a BPR Radio

    Cloning duplicates the contents of your radio (master radio) into the new radio (slave radio). Tuning and alignment information are not affected by cloning.

      Set Up the Master Radio:
    1. Turn off the radio.
    2. Press and hold Programmable Button 1 (the top programmable button) and turn on the radio. Keep pressing the Programmable Button 1 until beep is heard twice.
    3. Release Programmable Button 1. Notice the LED changes to RED

      Set Up the Slave Radio:
    1. Turn off the radio.
    2. Press and hold Programmable Button 1(the top programmable button) and turn on the radio. Keep pressing Programmable Button 1 until the beep is heard three times.
    3. Release Programmable Button 1. Notice that the LED changes to GREEN

      BPR40, BPR20 Radio to Radio Cloning Procedures:
    1. Connect the cloning cable to both the Master and Slave radio.
    2. Press and release Programmable Button 1 of the Slave radio.
    3. Within 2 seconds Press and release Programmable Button 1 of the Master radio.
    4. The LED for both radios show flashing orange during cloning.
    5. Once cloning is completed, an ‘Out Chirp’ alert tone can be heard from both radios.
    6. Disconnect radios from the cloning cable. They are now ready for operation.
    An error may occur when cloning a radio. When this happens, the radio sounds a Faulty Condition Alert tone and shows a Flashing Orange LED momentarily.

    **NOTE** The LED will illuminate in RED and the radio will keep transmitting if the cloning cable is still connected to the radio after cloning is completed. Please disconnect the cloning cable from the radio.

    Motorola Mag One PMDN4060AR Cloning Cable for BPR40, BPR20 2-Way Radios


    Clone additional Mag One BPR radios using your radio and cloning cable. No software or computer is needed. All settings are transferred to the new BPR radios including frequencies, power settings, and button assignments.

    This accessory makes it easy to buy additional radios and not have to worry about programming information. Models must be identical. Remove the batteries from both radios and make sure the model numbers (starts with AAH84) are an exact match. If not, you cannot use this cable.

    How To Clone a BPR Radio

    Cloning duplicates the contents of your radio (master radio) into the new radio (slave radio). Tuning and alignment information are not affected by cloning.

      Set Up the Master Radio:
    1. Turn off the radio.
    2. Press and hold Programmable Button 1 (the top programmable button) and turn on the radio. Keep pressing the Programmable Button 1 until beep is heard twice.
    3. Release Programmable Button 1. Notice the LED changes to RED

      Set Up the Slave Radio:
    1. Turn off the radio.
    2. Press and hold Programmable Button 1(the top programmable button) and turn on the radio. Keep pressing Programmable Button 1 until the beep is heard three times.
    3. Release Programmable Button 1. Notice that the LED changes to GREEN

      BPR40, BPR20 Radio to Radio Cloning Procedures:
    1. Connect the cloning cable to both the Master and Slave radio.
    2. Press and release Programmable Button 1 of the Slave radio.
    3. Within 2 seconds Press and release Programmable Button 1 of the Master radio.
    4. The LED for both radios show flashing orange during cloning.
    5. Once cloning is completed, an ‘Out Chirp’ alert tone can be heard from both radios.
    6. Disconnect radios from the cloning cable. They are now ready for operation.
    An error may occur when cloning a radio. When this happens, the radio sounds a Faulty Condition Alert tone and shows a Flashing Orange LED momentarily.

    **NOTE** The LED will illuminate in RED and the radio will keep transmitting if the cloning cable is still connected to the radio after cloning is completed. Please disconnect the cloning cable from the radio.

    Unsupported Browser

    We're sorry, your browser (Internet Explorer) is not supported. You will experience technical difficulties if you choose to continue. For the best experience, please open this website using an updated browser.

    Continue anyway
    Unsupported Browser

    We're sorry, your browser (Internet Explorer) is not supported. You will experience technical difficulties if you choose to continue. For the best experience, please open this website using an updated browser.

    Continue anyway